Need warranty zone panel Williams looking into warranty procedure Thermostats were randomly rebooting together. Tech support pointed me in the direction of communication bias. Went down that rabbit hole and didn't solve the issue. Removed zone panel from the equation, wired first floor stat directly to furnace and heatpump communication wires. Added refrigerant to the system. We will want to monitor this. No obvious leaks. 3-18-2025 Upon arrival, found zone panel blank. Tested transformer, it had failed. Range hood damper is also wired to this transformer. It appears to have been wired wrong and that's what killed the transformer. Powered on range hood and tested the pressure switch wire at the furnace with Ohm meter. Never got continuity. Because of this, I just wired the damper to stay open. Replaced transformer, added a 5A fuse to it. Ran stranded wire from transformer to zone panel. Based on these findings, decided to reconnect everything to original zone panel an

Perform heating PMI, clean burners and flame sensor. Test ran unit. No concerns at this time. Fixed leaking exhaust pipe. Informed homeowner of water leak developing on water heater to prevent finished basement damage. Informed homeowner of growth on humidifier and it’s currently inoperable. Could need a new humidistat unsure of actual conditions homeowner is not concerned over it at this time

1973 general electric 70% gas furnace is barely able to stay running due to heat exchanger stress, fatigue, and thinning of the metal causing the fan limit control to short cycle off at 200° every 3 minutes Combustion analysis and airstream carbon monoxide testing are all producing normal results except excessively high exhaust gas temperatures approaching 600° f *All carbon monoxide readings in the exhaust of the furnace are all reading below 10 PPM on every burner chamber and the airstream test for 15 minutes fluctuated between 0-2 ppm CO Homeowners have additional carbon monoxide testers in the bedroom System does not appear to be unsafe at this time except for the high discharge temperatures caused by the heat exchanger. Adjusted The gas valve manifold pressure down one full turn counterclockwise to reduce the heat and allow continuous operation. Temperature rise was lowered from 78 to 55 *Air filter has been removed permanently and system will overheat if a pleated style filt

Upon arrival inspected furnace and discovered a loose cooling wheel on inducer motor. After further inspection discovered dragging bearings on motor as well. Unit may have overheated to damage bearings but the motor is in bad health and should be replaced. Perform removal and replacement of inducer motor for Payne furnace. Unit comes as separate parts and needs assembled

Install New Bryant Preferred 2 Stage Gas Furnace Model #: 926TC48060V17 Serial #: 0625A46996 Installation: * Reconnect to existing gas line and high voltage electric * Transition to existing supply and return ductwork * Start up and commission new system * Aprilaire 1210 Media Air Cleaner * Aprilaire 600M Humidifier w/ Humidistat Warranty: 20 Year Bryant manufacturers heat exchanger warranty. 10 Year Bryant manufacturers parts warranty (Annual maintenance must be performed) 2 Year Westin Air labor warranty (Annual maintenance must be performed)

Inspected B vent inside and outside. It is good to be connected to.

Diagnosed failed inducer motor on furnace #2. Also found failed blower motor capacitor. This furnace and AC is inoperable until repairs are made. IF repairs are made, a full check will need to be performed to verify a healthy heat exchanger. Sent proposal for repairs on furnace #2. Parts are in stock. Performed maintenance checks on furnaces 1 and 3 Furnace 1 is very close to end of life. Combustion readings are at the high end of acceptable values. Inducer and associated exhaust piping has been leaking for some time now. As a result of the leaking, there is a serious amount of rust. Furnace #3 is in the best shape of all of them, but still nearing end of life according to the combustion test results. We recommend replacement of all 3 systems. List of priority from highest to lowest would be: system 2, system 1, then system 3. All three systems are 22 years old.

Performed heating maintenance on Carrier single stage 92% efficient furnace. Pulled and cleaned flame sensor Blew out Condensate trap Burners free of rust and are clean Blower is clean Filter is good Checked gas pressure, it was set to 1.6", specification is 3.0" Adjusted gas to 3.0 Temperature rise 40⁰ with final gas pressure adjustment Blower capacitor measured 10mfd, rated 10mfd

Replace Daikin Translation Adapter under Daikin parts warranty Spent hours on the phone with Daikin tech support. First, the translation adapter did not resolve the issue. There are multiple issues with the system. Many are related to installation. The furnace is constantly getting error codes related to the blower motor. This is due to restricted airflow from incorrect installation. The thermostat wiring going through the wall and basement ceiling is of thr wrong type and there is no way to pull a new wire without ripping out the finished ceiling. Tech support had me measure the signal strength along the wiring and it was out of specification. Last, the outdoor unit is having issues that we cannot for certain pin point the cause. Tech support and I believe it is the control board for the outdoor unit. Perfect resolution may be impossible. True solution is to remove the Daikin equipment and install something completely different.

Inspected natural gas Manifold for house and line to water heater. Found small gas leak on bottom piece of union. Disassembled gas line from union to tee into water heater, inspect for damage and cracks, and reseal and tighten gas line back down. Open gas shutoff and test for leaks. No other leaks found. Ignite pilot light and test operation of waterheater. No other gas leaks found after repair. George requested information and a quote for replacement of furnace and possibly the AC aswell. Furnace is from 1994, and AC is from 2014. Pictures uploaded to file to assist with quoting process.

Attempted to make the thermostat non-programmable mode. This thermostat does not have that provision. Explained putting thermostat into a permanent hold of the set temperature.

Upon arrival, discovered furnace in an inducer pressure switch stuck open state. After inspecting furnace discovered extreme heat built up in inducer motor and it was still running. Turn power off two unit and checked inducer motor run capacitor. Run capacitor tested open line reading bad. Install 7.5 run capacitor on inducer to test run furnace and verify inducer motor does not get stuck on. Unit fired up and ran healthy as normal and fully shut down as needed. Inducer motor sounds normal but motor built up lots of heat during runtime with a bad capacitor. Informed homeowner inducer motor may be damaged but as of now everything is okay.

Investigated rattling on furnace. Setup an extension ladder. We really need 12' A frame ladder next time. Adjusted the unistrut in the ceiling as it was the source of the rattle.

Modify supply and return plenum to allow the following: *Pitch furnace forward and level left to right. *Increase transition in RA drop. *Relocate exhaust PVC 3-2 reducer to a vertical position.

Performed heating maintenance on a Trane two stage natural gas furnace. Pulled and cleaned flame sensor Pulled and flushed condensate trap with water Replaced air filter High fire gas set to 3.5" Temperature rise 43⁰ Low fire gas pressure 1.8" Temperature rise 40⁰ Ran combustion test. Heat exchanger health is perfect. Tested humidifier, no water leaks at this time Furnace is operating within manufacturer's specifications at this time.

Performed heating maintenance on a Trane all electric heat pump system. Filter is good 44 degree outdoor ambient Vapor line temperature at the air handler 126 degrees 21 degree temperature rise without auxiliary heat running. Tested auxiliary heat: Temperature rise 48 degrees without the heat pump running All wiring secure and tight No signs of overheating of the wiring All three heat elements are drawing 20A each Blower and indoor coil are both clean Outdoor coil is clean No concerns with the wiring inside the heat pump control panel. Compressor Amp draw 8.1 (14.1 max rated) Outdoor fan 0.6A (0.64 rated) Forced unit into defrost mode. Changeover was smooth Secured wiring for reversing valve and defrost temperature sensor with zip ties so they are not touching any of the refrigerant tubing (over time this can cause a short circuit) Also adjusted the tubing for the outdoor TXV sensing bulb: it had been rubbing against the fins of thr removable panel. System is in great shape and oper

Went through furnace. See notes. Customer declines replacement at this time.

Install all new furnace vent piping including concentric termination. Remove and patch humidifier opening.

Upon arrival inspected furnace and found no major concerns. Test ran system by thermostat and unit would only kick on with thermostat maxed out and while holding stat in that position if you let go unit would turn back off. Thermostat is an old mercury thermostat and needs replaced. Remove and replace with T4 battery thermostat, test run furnace and no major concerns with new thermostat. Unit is filthy. Has been running for a long time with no filter. Ac will probably not work and heat may not be consistent. If problems arise in the future we will have to pull the blower assembly and clean it as well as open up the ac coil and clean it. Ac is an old ruud unit and may not be functional to begin with outdoor air too cold to test cooling system

Upon arrival discovered no major concerns. Aside from furnace reading code E09 on board diag reads that is a pressure switch stuck closed Furnace is of old age, having odd out flukes and errors homeowner prefers to replace and get a more reliable system overall. House square footage is 2,300 she would like an ac with the quote and sticker on unit is faded beyond recognition

Upon arrival for basic gas furnace maintenance and PMI the homeowner special requests and concerns include burning eyes and odor after long run times, resealing the falling apart thumb gum putty at the line set and drain penetrations of the plenum, and inability to connect vision pro 8000 to Wi-Fi or the account Full system 80% gas heating furnace tune up, maintenance, cleaning, safety inspection. Replace 16X25x1 air filter provided by homeowner, resurface flame sensor and burners, test run hot surface igniter, run test heat mode for correct temperature rise at 124°f and carbon monoxide in the airstream. Airstream carbon monoxide test detected (zero) 0 PPMs of carbon monoxide after 20 - 30 minute run test. Centralized carbon monoxide test at the dining room table also produced 0 PPMs carbon monoxide after 10 to 15 minutes of additional run time Reconnect vision pro 8000 to new Wi-Fi Homeowner will contact customer support phone number for residio to confirm account & thermostat is

Upon arrival discovered igniter on 2nd floor unit was left unplugged from previous maintenance visit, causing furnace to go into a code E6.3 ignition proving failure. Test ran unit after fixing igniter and no problems occurred after.

Upon arrival inspected furnace and found a dirty filter from 1-27-25 filter is not old enough to need replaced but is dirty and needs replaced. Informed homeowner of heavy buildup at return vents and behind couch for lower return possibly causing excessive buildup. Static pressure with dirty filter 0.99R 0.42S new filter 0.46R 0.66S. Unit will continue to fault with dirty filters. Solution may be expanding filter from 16x25x1 to 1210AA (20x25x4 Popup) increasing filter life and airflow even with clogged filter will be less restrictive

Upon arrival furnace was operating but homeowner stated unit doesn’t run constantly as intended/when needed. Inspected furnace and discovered clogged flu vent, full of twigs and dust. After cleaning vent pipe test ran furnace and unit seems to be running in a much better state. No longer having any issues keeping unit on.

Upon arrival furnace was operating in low fire heat. Discovered mildly clogged 20x25x4 filter, homeowner replaced the filter and then I inspected the furnace and discovered unit was in need of a cleaning. Pull and wire brush burners and rinse clogged drain in sink. Test ran furnace after cleaning no issues occurred.